返回集团首页
欢迎来到富达金官网!
location:Home >> Solution >> Cabinet light solution

DO NOT USE WITH DIMMERS

SUITABLE FOR WET LOCATIONS

SUITABLE FOR OPERATION IN AMBIENT NOT EXCEEDING 45℃

WARNING-RISK OF FIRE OR ELECTRIC SHOCK. NOT FOR DIRECT

REPLACEMENT OF FLUORESCENT LAMPS. USE WITH SHENZHEN

FUDAKIN DISPLAY LIGHTING CO LTD.(E491468) FSL-LD2-10024V

VOLAGE:120-277VAC

LED RETROFIT LUMINAIRE CONVERSION

FOR USE ONLY WITH COMMERCIAL

REFRIGERATORS AND FREEZERS

IN ACCORDANCE WITH THE INSTRUCTIONS

PROVIDED WITH THIS RETROFIT KIT

This Iuminaire has been modified to operate LED lamps.DO not attempt to install or operate fluorescent lamps in this luminaire.Replacement LED Lamp type FDK-FSL-F0-XXX-XXX-XXX-D-C93 with manufacturer ShenZhen FUDAKAN Display Lighting Co.,Ltd

Product Features:

Best Green Industrial Lighting

-Ideal for warehouses,factories,cold storage,stadiums,rinks

-Not affected by cold weather

-No warm up or cool down needed

-Instant on at full output no lag time for warehouse safety

High Efficiency and Long Lifetime

-60% less energy than a traditional
70W MH/HPS

-Engineered heat disssipation for longger life

-Rated 50,000 hrs

Total Green

-No UV, no infraed, no radiated heat

-Cuts power consumption

-100% Recyclable

-Cuts CO2 emissions

-RoHS certified

Application

-Vertical coolers

-Walk-in cooler

-Refrigerated display

-Deep well fridge

Create a fixture with F0 LED engines

Wiring diagram

WARNING!

i) Please read and follow the carefully before installation.

ii) For wet location.

iii) Only by licensed electrician.

iv) Power must be turned off installation.

v) Limited warranty

vi) Only operate product with voltage and frequency stated on this instruction.

WARNING:

"WARNING - Risk of fire or electric shock.LED Retrofit Kit requires knowledge of luminaire electrical systems.If not qualified,do not attempt installation.Contact a qualified electrican."

"WARNING - Risk fire or electric shock.Install this kit only in luminaires that have the construction features and dimensions in the photographs and/or drawings and where the input rating of the retrofit kit does exceed the input rating of the luminaire."

"WARNING - To prevent wiring damage or abrasion,do not wiring to edges of sheet metal or other sharp objects."

Only those open holes indicated in the and/or drawings may be made or as a result of kit installation.
Do not leave any other open holes in an of wiring or electrical components.

"WARNING - Risk of fire or electric shock. Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.”

"WARNING - To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.”

"Installers should not disconnect existing wires from lampholder terminals to make new connections at lampholder terminals. Instead installers should cut existing lampholder leads away from the lampholder and make new electrical connections to lampholder lead wires by employing applicable connectors."

"THIS RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY AUTHORITIES HAVING JURISDICTION."

"WARNING -Risk of fire or electric shock. Do not connect driver to output connector of Light Strip"

Examine all parts that are not intended to be replaced by the retrofit kit for damage and replace any damaged parts prior to installation of the retrofit kit

a.If the light fixture is providing with magnetic ballast,the wires at the point as shown in the following figures (see Figure 1) Remove all ballast ,lampholders and starters.

Figure 1:Cut the wires

b.If the light fixture is providing with electronic ballast,disconnect the wires at the point as shown in the following figures (see Figure 2),remove all the lampholders and ballast.

Figure 2:Cut the wires

c:Install the LED driver to a suitable place of refrigerator (or refrigeration system) or freezers (for example: the compartment of original ballast). Please ensure the LED driver and all the high voltage splices are enclosed by enclosure and kept away from water and liquid.

d:After modification completed, attach the Lamping Marking Label and Cautionary L abel which provided with the retrofit kit to the light fixture.The labels shall be visible relamping.